BCM3380A1 TP0
1
Sync:1
346890
MemSize: 128 M
BootLoader Version: 2.3.1LxGalpha3R4 Pre-release Gnu spiboot reduced DDR drive
Build Date: Jan 20 2011
Build Time: 16:07:38
SPI flash ID 0x012018, size 16MB, block size 64KB, write buffer 256, flags 0x0
Dual flash detected. Size is double the above.
Signature/PID: a0d3
Reset BCM53115 - Low GPIO-18 10ms
Image 1 Program Header:
Signature: a0d3
Control: 0005
Major Rev: 0003
Minor Rev: 0000
Build Time: 2013/6/5 02:33:55 Z
File Length: 4030489 bytes
Load Address: 80004000
Filename: CG3100L_E15R392113V0031_NUM_130605.bin
HCS: 6db2
CRC: e11d7a29
Found image 1 at offset 20000
MAX SIZE: 23068672
Image 3 Program Header:
Signature: a0d3
Control: 0105
Major Rev: 0002
Minor Rev: 0017
Build Time: 2013/6/5 02:09:31 Z
File Length: 6537124 bytes
Load Address: 84010000
Filename: CG3100L_K2630V0031_NUM_130605.bin
HCS: 7be7
CRC: 5a57e5c0
Found image 3 at offset 800000
Enter '1', '2', or 'p' within 2 seconds or take default...
. .
Performing CRC on Image 3...
CRC time = 232493827
Detected dual image header. Decompressing first image...
Detected LZMA compressed image... decompressing...
Target Address: 0x84010000
decompressSpace is 0x8000000
Elapsed time 1283043792
Decompressed length: 4530944
Boot command: 'root=31:0 ro noinitrd rootfstype=squashfs panic=1 console=ttyS0,115200 imgoffset=0x00800000 sig=3380'
Done Decompressing Image 3...
Performing CRC on Image 1...
CRC time = 299021544
Detected LZMA compressed image... decompressing...
Target Address: 0x80004000
decompressSpace is 0x8000000
Elapsed time -1464295087
Decompressed length: 19336371
Copying partition table to 0x83fffc04 160
Executing Image 1...
eCos - hal_diag_init
Init device '/dev/BrcmTelnetIoDriver'
Init device '/dev/ttydiag'
Init tty channel: 81274728
Init device '/dev/tty0'
Init tty channel: 81274748
Init device '/dev/haldiag'
HAL/diag SERIAL init
Init device '/dev/ser0'
BCM 33XX SERIAL init - dev: 0.2
Set output buffer - buf: 0x814a3170 len: 4096
Set input buffer - buf: 0x814a4170 len: 4096
BCM 33XX SERIAL config
Init device '/dev/ser1'
BCM 33XX SERIAL init - dev: 0.3
Set output buffer - buf: 0x814a5170 len: 4096
Set input buffer - buf: 0x814a6170 len: 4096
BCM 33XX SERIAL config
LsSpiInit 3380
ChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2
BcmBfcAppNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULLChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2
, and someone is accessing it!
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver...
[00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash: (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0x12018
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::FlashDriverInit: (Flash Driver C API) WARNING - Failed to retrieve the memory window associated with flash device 1!
[00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::FlashDriverInit: (Flash Driver C API) WARNING - Failed to detect flash device 1! Only the first device will be use.
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver...
ProgramStoreDeviceDriver::ProgramStoreDriverInit: INFO - Initializing...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver...
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully.
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices...
Detecting the next image number that we will store to by default...
Bootloader indicates we are running image 1
By default, we will dload to image number 2!
[00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully.
BcmCmVendorNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it!
BcmCmVendorNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it!
[Numericable] Init US Table
[Numericable] Init US Table
[Numericable] Init US Table
[Numericable] Init US Table
BcmCapNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it!
BcmEmtaSnmpNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it!
WARNING: ResetDefaultBlindEmtaData() -Resetting EMTA non-vol data section to default values
mtaNvCalcChecksum: checksum= 1273101785
Reading Permanent settings from non-vol...
Checksum for permanent settings: 0xe3fd5c64
[00:00:00 01/01/1970] [tStartup] BcmWiFi80211NonVolSettings::ReadFromImpl: (WiFi 802.11 NonVol Settings) WARNING - Read older version of the settings (0.9); they have .
[00:00:00 01/01/1970] [tStartup] BcmCmDocsis30NonVolSettings::ReadFromImpl: (CM DOCSIS 3.0 NonVol Settings) WARNING - Read older version of the settings (0.1); they ha.
[00:00:00 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (CM BFC Event Log) Permanent settings are default!
[00:00:00 01/01/1970] [tStartup] BcmWiFi80211HomeHotspotNonVolSettings::IsDefault: (WiFi 802.11 Home Hotspot NonVol Settings) Permanent settings are default!
[00:00:00 01/01/1970] [tStartup] BcmeRouterIpv6FirewallNonVolSettings::IsDefault: (IPv6 Firewall NonVol Settings) Permanent settings are default!
[00:00:00 01/01/1970] [tStartup] BcmeRouterDhcpV6ServerNonVolSettings::IsDefault: (eRouter DhcpV6 Server NonVol Settings) Permanent settings are default!
[00:00:00 01/01/1970] [tStartup] BcmMscNonVolSettings::IsDefault: (Media Server Control NonVol Settings) Permanent settings are default!
[00:00:00 01/01/1970] [tStartup] BcmNasNonVolSettings::IsDefault: (NAS NonVol Settings) Permanent settings are default!
[00:00:00 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (EMTA BFC Event Log) Permanent settings are default!
*
*
* One or more of the settings groups was missing, possibly as a result of a code upgrade.
*
*
*
*
* One or more of the settings groups was upgraded.
*
*
Settings were read and verified.
Reading Dynamic settings from non-vol...
Checksum for dynamic settings: 0xb590005e
~~~ count: 0
[00:00:00 01/01/1970] [tStartup] BcmWiFi80211HomeHotspotNonVolSettings::ResetDefaults: (WiFi 802.11 Home Hotspot NonVol Settings) WARNING - 802.11 settings are being r!
we found one in the table already!!!!
Settings were read and verified.
Console input has been disabled in non-vol.
Console output has been disabled in non-vol! Goodbye...