BCM3380A1 TP0 1 Sync:1 346890 MemSize: 128 M BootLoader Version: 2.3.1LxGalpha3R4 Pre-release Gnu spiboot reduced DDR drive Build Date: Jan 20 2011 Build Time: 16:07:38 SPI flash ID 0x012018, size 16MB, block size 64KB, write buffer 256, flags 0x0 Dual flash detected. Size is double the above. Signature/PID: a0d3 Reset BCM53115 - Low GPIO-18 10ms Image 1 Program Header: Signature: a0d3 Control: 0005 Major Rev: 0003 Minor Rev: 0000 Build Time: 2013/6/5 02:33:55 Z File Length: 4030489 bytes Load Address: 80004000 Filename: CG3100L_E15R392113V0031_NUM_130605.bin HCS: 6db2 CRC: e11d7a29 Found image 1 at offset 20000 MAX SIZE: 23068672 Image 3 Program Header: Signature: a0d3 Control: 0105 Major Rev: 0002 Minor Rev: 0017 Build Time: 2013/6/5 02:09:31 Z File Length: 6537124 bytes Load Address: 84010000 Filename: CG3100L_K2630V0031_NUM_130605.bin HCS: 7be7 CRC: 5a57e5c0 Found image 3 at offset 800000 Enter '1', '2', or 'p' within 2 seconds or take default... . . Performing CRC on Image 3... CRC time = 232493827 Detected dual image header. Decompressing first image... Detected LZMA compressed image... decompressing... Target Address: 0x84010000 decompressSpace is 0x8000000 Elapsed time 1283043792 Decompressed length: 4530944 Boot command: 'root=31:0 ro noinitrd rootfstype=squashfs panic=1 console=ttyS0,115200 imgoffset=0x00800000 sig=3380' Done Decompressing Image 3... Performing CRC on Image 1... CRC time = 299021544 Detected LZMA compressed image... decompressing... Target Address: 0x80004000 decompressSpace is 0x8000000 Elapsed time -1464295087 Decompressed length: 19336371 Copying partition table to 0x83fffc04 160 Executing Image 1... eCos - hal_diag_init Init device '/dev/BrcmTelnetIoDriver' Init device '/dev/ttydiag' Init tty channel: 81274728 Init device '/dev/tty0' Init tty channel: 81274748 Init device '/dev/haldiag' HAL/diag SERIAL init Init device '/dev/ser0' BCM 33XX SERIAL init - dev: 0.2 Set output buffer - buf: 0x814a3170 len: 4096 Set input buffer - buf: 0x814a4170 len: 4096 BCM 33XX SERIAL config Init device '/dev/ser1' BCM 33XX SERIAL init - dev: 0.3 Set output buffer - buf: 0x814a5170 len: 4096 Set input buffer - buf: 0x814a6170 len: 4096 BCM 33XX SERIAL config LsSpiInit 3380 ChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2 BcmBfcAppNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULLChipHalSelectPinMux: Setting pin mux sel 18, word 0, value 2 , and someone is accessing it! [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Configuring/Loading Flash driver... [00:00:00 01/01/1970] [tStartup] BcmSpiFlashDevice::DetectFlash: (SPI Flash Device Factory) WARNING - Detected SPI flash with JEDEC ID =0x12018 [00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::FlashDriverInit: (Flash Driver C API) WARNING - Failed to retrieve the memory window associated with flash device 1! [00:00:00 01/01/1970] [tStartup] FlashDeviceDriver::FlashDriverInit: (Flash Driver C API) WARNING - Failed to detect flash device 1! Only the first device will be use. [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading BootloaderStore driver... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading ProgramStore driver... ProgramStoreDeviceDriver::ProgramStoreDriverInit: INFO - Initializing... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Loading NonVol driver... [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitStorageDrivers: (BFC Target) Storage drivers initialized successfully. [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Creating singletons for ProgramStore/BootloaderStore/NonVol devices... Detecting the next image number that we will store to by default... Bootloader indicates we are running image 1 By default, we will dload to image number 2! [00:00:00 01/01/1970] [tStartup] BcmBfcStdEmbeddedTarget::InitDeviceAbstractions: (BFC Target) Device abstraction singletons created successfully. BcmCmVendorNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! BcmCmVendorNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! [Numericable] Init US Table [Numericable] Init US Table [Numericable] Init US Table [Numericable] Init US Table BcmCapNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! BcmEmtaSnmpNonVolSettings::GetSingletonInstance: WARNING - the singleton instance is NULL, and someone is accessing it! WARNING: ResetDefaultBlindEmtaData() -Resetting EMTA non-vol data section to default values mtaNvCalcChecksum: checksum= 1273101785 Reading Permanent settings from non-vol... Checksum for permanent settings: 0xe3fd5c64 [00:00:00 01/01/1970] [tStartup] BcmWiFi80211NonVolSettings::ReadFromImpl: (WiFi 802.11 NonVol Settings) WARNING - Read older version of the settings (0.9); they have . [00:00:00 01/01/1970] [tStartup] BcmCmDocsis30NonVolSettings::ReadFromImpl: (CM DOCSIS 3.0 NonVol Settings) WARNING - Read older version of the settings (0.1); they ha. [00:00:00 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (CM BFC Event Log) Permanent settings are default! [00:00:00 01/01/1970] [tStartup] BcmWiFi80211HomeHotspotNonVolSettings::IsDefault: (WiFi 802.11 Home Hotspot NonVol Settings) Permanent settings are default! [00:00:00 01/01/1970] [tStartup] BcmeRouterIpv6FirewallNonVolSettings::IsDefault: (IPv6 Firewall NonVol Settings) Permanent settings are default! [00:00:00 01/01/1970] [tStartup] BcmeRouterDhcpV6ServerNonVolSettings::IsDefault: (eRouter DhcpV6 Server NonVol Settings) Permanent settings are default! [00:00:00 01/01/1970] [tStartup] BcmMscNonVolSettings::IsDefault: (Media Server Control NonVol Settings) Permanent settings are default! [00:00:00 01/01/1970] [tStartup] BcmNasNonVolSettings::IsDefault: (NAS NonVol Settings) Permanent settings are default! [00:00:00 01/01/1970] [tStartup] BcmNonVolSettings::IsDefault: (EMTA BFC Event Log) Permanent settings are default! * * * One or more of the settings groups was missing, possibly as a result of a code upgrade. * * * * * One or more of the settings groups was upgraded. * * Settings were read and verified. Reading Dynamic settings from non-vol... Checksum for dynamic settings: 0xb590005e ~~~ count: 0 [00:00:00 01/01/1970] [tStartup] BcmWiFi80211HomeHotspotNonVolSettings::ResetDefaults: (WiFi 802.11 Home Hotspot NonVol Settings) WARNING - 802.11 settings are being r! we found one in the table already!!!! Settings were read and verified. Console input has been disabled in non-vol. Console output has been disabled in non-vol! Goodbye...